There are several steps you need to take so that you can install a submersible well pump. First, you need to ensure you have followed all steps as indicated in the installation manual. A submersible pump will work hen immersed in water. You need to ensure you come up with a secure assembly which you can lower into the water.
Start by taking measurements of the depth of your well before you can proceed to lower the pump. Remember, it is necessary to take the measurements so that you can know the amount of materials and piping you require before you can lower the unit into the water. Here are some steps you need to take so that you can have a secure system in place to help you get enough water supply for your daily use:
Contents
- The Ways: Submersible pump installation methods and safety system
- 1. Measure the well total depth
- 2. Drawdown water level
- 3. Well capacity
- 4. Safety measures
- 5. Check manufacturer installation instructions
- 6. Protect pump and piping against freezing temperatures
- 7. Wear gloves and eye protection during installation
- 8. Ground fault interrupter
- 9. Ensure the voltage meets the manufacturer recommendations
- 10. Ensure the motor is well-grounded
The Ways: Submersible pump installation methods and safety system
1. Measure the well total depth
The well overall depth is the length from the ground surfaces to the bottom of the well. It is necessary to take the measurements because it will make it easy for you to plan for the essential materials you need to get the unit running. There are several steps you need to take before you can take the measurements. You need a tape measure and a way you can drop it to the bottom of the well.
2. Drawdown water level
It is the amount of water in the well and the height it occupies. It is necessary to take note of this level because it will keep on fluctuating as you draw the water from the pump. You need to install the submersible pump below the draw down water level. It is necessary so that you can avoid cases where the pump will run dry.
3. Well capacity
You need to check on the well capacity. It is necessary to have information about the well capacity so that you can know the amount of water you expect to get out of the well. The best pump to buy should be able to deliver enough water for your everyday use. Take time to assess the capacity of the pump and the water available in the well. There is no need to install a powerful pump in a well which can run dry after a few hours.
4. Safety measures
There are several safety measures you need to take into consideration before you can proceed to invest in a well pump installation project. Here are some of the safety measures you need to take into consideration before you can proceed to get a well pump in place:
5. Check manufacturer installation instructions
Installation procedures will accompany the pump, you need to take into consideration the installation procedures so that you can get it easy as you go about the installation process. Ensure you take time to go over the installation instructions before you can proceed to install the pump. It will be easy for you to get the installation steps right if you can follow the recommendations. There are several brands of well pumps out there. Each brand will have the installation instructions. You need to follow the instruction and it will be easy to get the pump ready for work. Ensure you follow all the steps listed and it will be easy for you to get the pump up and running as fast as possible.
6. Protect pump and piping against freezing temperatures
A submersible pump requires protection against freezing. If you stay in a place where winter is extreme, then you need to take the safety measure of protecting the pump against freezing. You will have to install some form of insulation which can avoid the pipes from bursting during winter.
7. Wear gloves and eye protection during installation
You need basic protection as you work on the well pump installation process. Ensure you wear protective gloves as you work on the pump. It is necessary because it will play a great role in helping you get the necessary protection. You may have to tighten some parts which increase the risk of chipping jumping. It is necessary to wear protective gear before you start the installation process. The simple safety measures you will take will play a great role in helping you get the unit in place. Always ensure you follow the right steps, and it will be easy for you to get the unit up and to run.
8. Ground fault interrupter
The ground fault interrupter is necessary to avoid cases where you can end up with accidents as you operate the unit. In most cases, the manufacturers will indicate the necessary points where you are supposed to have the ground fault interrupters. You need to have them in place, and they will play a great rowel towards helping you get the unit in place and make it work correctly.
9. Ensure the voltage meets the manufacturer recommendations
Some pumps are rates 120 volts while others are rated 240 volts. You need to check on the motor ratings before you can proceed to install. Always ensure your source of electricity meets the requirements of the manufacturer’s recommendations. It is necessary to avoid cases where you can end up damaging your unit due to exposing it to the wrong voltage. It is necessary to check out the voltage requirements before you can proceed to buy a given unit. It should be highly effective and reliable to make it easy for you when installing it.
10. Ensure the motor is well-grounded
The motor should be ground to avoid cases where it will expose you to electrical shocks. The grounding should be done while adhering to the right steps. There are several methods you can go about it. It will take you a few minutes to follow the instructions. You need to follow the right steps while installing the pump, and it will serve you for long. Ensure you choose the right submersible pump for your given applications, and it will work perfectly to allow you to realize the best performance as you try to keep the pump running perfectly. Installing a submersible pump is a great idea as it will make it easy for your family members to draw water for everyday use.
Read More:
