There are several steps you need to take before you can install a submersible pump in a bore well. Ensure you check on the depth of the bore well then install the pump the right way. There are several well pumps available in the market. You need to research widely and locate the best pump. Having the right pump in place is necessary. It will play a great role in making you have a reliable water supply system.
When a well pump is installed the right way, it will work perfectly in allowing you to realize the best results as you try to access water for daily use. Most well pumps come with instructions on how to install them, it will be easy to install it if you can follow the instruction manual. Here are some of the steps you need to take so that you can install a water pump the right way:
The Ways to Install a Submersible Pump in Borewell
Check the bore well and ensure it is in good condition
Before you can start the pump installation process, you need to inspect the pump and locate any signs of external damage to the casing. The well may fail after a short while making your investment go to waste if the well casing has broken or it has other defects. It is necessary to inspect the well and take care of any damage before you can proceed to install the pump.
After you inspect the bore well and ensure it is in good condition, you should take the measurements of the well head. The submersible pump will be installed inside the water. You need to check on the level of the water after which you can proceed to install it. The best well pump to install should be of the highest quality so that it can assure you the best performance. Check on the depth so that you can plan well on the cables and the piping.
Check the submersible pump components
Before you start the assembly, you need to ensure the supplied pump is working. You can check the components and test whether the circuit is working. You can as well have an assembly and test it to draws water from a bucket. Remember the bore well is small.
You will not be able to enter the well so that you can install the pump. You will have to do the whole assembly on the surface then lower the components to the bottom of the bore well where the pump will come into contact with water so that the pumping action can commence. It is a simple process you can undertake, and it will work correctly in helping you draw water from the bore well.
Lay the assembly next to well and test to ensure it is working
After you have assembled the pump and the piping, you need to ally it close to the pump where you will carry out tests to ensure it is working. You can have the whole assembly, which looks similar for the entire unit. It is necessary to lay it close to the bore well so that you can inspect it. Go over the installation manual and check whether you have followed all the instructions.
It will be easy for you to get the procedure right if you can work closely with the manufacturer’s details. The several brands of pumps available in the market will tend to differ based on several factors. It is necessary to ensure you follow the installation manual before you can proceed. Inspect the assembly and ensure all parts are secure. It is necessary to avoid cases where some parts can come off as you try to lower it into the well.
Lower the assembly into the well water
You need to lower the assembly until it enters the water in the borehole. The submersible pump will only work after you make it get submerged in the water. Ensure you lower it till it touches the water level. You need to be careful as you lower it to avoid cases where you can cause damage to the assembly. You can use pipes to secure it so that it can stand in place. It is essential to keep a note of the borehole depth. If the depth is long, then you will have to use long cables and pipes to secure the assembly as you lower them to the water surface.
Secure the assembly in position
After you have lowered the unit to the water level, then it is time to secure the assembly. Ensure the assembly is secured well so that it can pump the water out of the well. Take necessary measures to ensure the assembly is well secured. Remember, vibrations can easily interfere with the working of the assembly.
In most cases, the manufacturers will provide photos and a clear description of what you are supposed to do so that you can secure the unit in place. Ensure you follow the details, and it will be easy for you to secure the assembly. It will be easy for you to secure the unit if you can follow the right steps. Always ensure you follow the right steps, and it will be easy to get the pump up and running as soon as you buy it. Some pumps will come with a manufacturer’s warranty, ensure you follow the instructions to avoid cases where you can end up interfering with the manufacturer’s warranty.
Connect a starter motor and start the pump
A pump start will be accessible to you so that you can stop and start the pump. The rest of the assembly will be submerged in water, but you will have the start at the surface of the well. You need to connect the start to the pump before you can start using it. The starter will be connected to the pump motor via cables, ensure the cables are watertight. You can sue splice cable construction provided to have a secure connection. It is necessary to ensure the connection is secure and watertight so that it can assure you the best operation as you try to operate the water pump.
Read More:
